2 # Texas Instruments DaVinci family: TMS320DM6446
4 if { [info exists CHIPNAME] } {
5 set _CHIPNAME $CHIPNAME
11 # For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB
12 # are enabled without making ICEpick route ARM and ETB into the JTAG chain.
13 # Override by setting EMU01 to "-disable".
15 # Also note: when running without RTCK before the PLLs are set up, you
16 # may need to slow the JTAG clock down quite a lot (under 2 MHz).
18 source [find target/icepick.cfg]
22 # Subsidiary TAP: unknown ... must enable via ICEpick
23 jtag newtap $_CHIPNAME unknown -irlen 8 -disable
24 jtag configure $_CHIPNAME.unknown -event tap-enable \
25 "icepick_c_tapenable $_CHIPNAME.jrc 3"
27 # Subsidiary TAP: C64x+ DSP ... must enable via ICEpick
28 jtag newtap $_CHIPNAME dsp -irlen 38 -ircapture 0x25 -irmask 0x3f -disable
29 jtag configure $_CHIPNAME.dsp -event tap-enable \
30 "icepick_c_tapenable $_CHIPNAME.jrc 2"
32 # Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
33 if { [info exists ETB_TAPID ] } {
34 set _ETB_TAPID $ETB_TAPID
36 set _ETB_TAPID 0x2b900f0f
38 jtag newtap $_CHIPNAME etb -irlen 4 -irmask 0xf -expected-id $_ETB_TAPID $EMU01
39 jtag configure $_CHIPNAME.etb -event tap-enable \
40 "icepick_c_tapenable $_CHIPNAME.jrc 1"
42 # Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
43 if { [info exists CPU_TAPID ] } {
44 set _CPU_TAPID $CPU_TAPID
46 set _CPU_TAPID 0x07926001
48 jtag newtap $_CHIPNAME arm -irlen 4 -irmask 0xf -expected-id $_CPU_TAPID $EMU01
49 jtag configure $_CHIPNAME.arm -event tap-enable \
50 "icepick_c_tapenable $_CHIPNAME.jrc 0"
52 # Primary TAP: ICEpick-C (JTAG route controller) and boundary scan
53 if { [info exists JRC_TAPID ] } {
54 set _JRC_TAPID $JRC_TAPID
56 set _JRC_TAPID 0x0b70002f
58 jtag newtap $_CHIPNAME jrc -irlen 6 -irmask 0x3f -expected-id $_JRC_TAPID
60 # GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 8K)
61 # and the ETB memory (4K) are other options, while trace is unused.
62 # Little-endian; use the OpenOCD default.
63 set _TARGETNAME $_CHIPNAME.arm
65 target create $_TARGETNAME arm926ejs -chain-position $_TARGETNAME
66 $_TARGETNAME configure -work-area-phys 0x0000a000 -work-area-size 0x2000
68 # be absolutely certain the JTAG clock will work with the worst-case
69 # CLKIN = 20 MHz (best case: 30 MHz) even when no bootloader turns
70 # on the PLL and starts using it. OK to speed up after clock setup.
72 $_TARGETNAME configure -event "reset-start" { jtag_rclk 1500 }
74 arm7_9 fast_memory_access enable
75 arm7_9 dcc_downloads enable
78 etm config $_TARGETNAME 16 normal full etb
79 etb config $_TARGETNAME $_CHIPNAME.etb