1 # script for stm32f4x family
4 # stm32 devices support both JTAG and SWD transports.
6 source [find target/swj-dp.tcl]
7 source [find mem_helper.tcl]
9 if { [info exists CHIPNAME] } {
10 set _CHIPNAME $CHIPNAME
12 set _CHIPNAME stm32f4x
17 # Work-area is a space in RAM used for flash programming
19 if { [info exists WORKAREASIZE] } {
20 set _WORKAREASIZE $WORKAREASIZE
22 set _WORKAREASIZE 0x10000
26 if { [info exists CPUTAPID] } {
27 set _CPUTAPID $CPUTAPID
30 # See STM Document RM0090
31 # Section 38.6.3 - corresponds to Cortex-M4 r0p1
32 set _CPUTAPID 0x4ba00477
34 set _CPUTAPID 0x2ba01477
38 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
40 if { [info exists BSTAPID] } {
43 # See STM Document RM0090
45 # STM32F405xx/07xx and STM32F415xx/17xx
46 set _BSTAPID1 0x06413041
47 # STM32F42xxx and STM32F43xxx
48 set _BSTAPID2 0x06419041
49 # See STM Document RM0368 (Rev. 3)
51 set _BSTAPID3 0x06423041
53 set _BSTAPID4 0x06433041
54 # See STM Document RM0383 (Rev 2)
56 set _BSTAPID5 0x06431041
60 swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
61 -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
62 -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
65 set _TARGETNAME $_CHIPNAME.cpu
66 target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
68 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
70 set _FLASHNAME $_CHIPNAME.flash
71 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
73 # JTAG speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
75 # Since we may be running of an RC oscilator, we crank down the speed a
76 # bit more to be on the safe side. Perhaps superstition, but if are
77 # running off a crystal, we can run closer to the limit. Note
78 # that there can be a pretty wide band where things are more or less stable.
81 adapter_nsrst_delay 100
86 reset_config srst_nogate
89 # if srst is not fitted use SYSRESETREQ to
90 # perform a soft reset
91 cortex_m reset_config sysresetreq
94 $_TARGETNAME configure -event examine-end {
95 # DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
96 mmw 0xE0042004 0x00000007 0
98 # Stop watchdog counters during halt
99 # DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
100 mmw 0xE0042008 0x00001800 0
103 $_TARGETNAME configure -event trace-config {
104 # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
105 # change this value accordingly to configure trace pins
107 mmw 0xE0042004 0x00000020 0