2 # Written by Uwe Hermann <uwe@hermann-uwe.de>, released as public domain.
3 # Modified by Piotr Esden-Tempski <piotr@esden.net>, released as public domain.
6 # Requirements (example is for Debian, replace package names as needed):
8 # apt-get install flex bison libgmp3-dev libmpfr-dev libncurses5-dev \
9 # libmpc-dev autoconf texinfo build-essential
11 # Or on Ubuntu Maverick give `apt-get build-dep gcc-4.5` a try.
14 # Stop if any command fails
17 ##############################################################################
18 # Default settings section
19 # You probably want to customize those
20 # You can also pass them as parameters to the script
21 ##############################################################################
22 TARGET=arm-none-eabi # Or: TARGET=arm-elf
23 PREFIX=${HOME}/sat # Install location of your final toolchain
24 DARWIN_OPT_PATH=/opt/local # Path in which MacPorts or Fink is installed
25 # Set to 'sudo' if you need superuser privileges while installing
27 # Set to 1 to be quieter while running
29 # Set to 1 to use linaro gcc instead of the FSF gcc
31 # Set to 1 to enable building of OpenOCD
33 # Set to 1 to build libstm32 provided by ST
35 # Set to 1 to build libopenstm32 an open source library for stm32
37 # Make the gcc default to Cortex-M3
38 DEFAULT_TO_CORTEX_M3=0
39 # Override automatic detection of cpus to compile on
42 ##############################################################################
43 # Parsing command line parameters
44 ##############################################################################
46 while [ $# -gt 0 ]; do
49 TARGET=$(echo $1 | sed 's,^TARGET=,,')
52 PREFIX=$(echo $1 | sed 's,^PREFIX=,,')
55 DARWIN_OPT_PATH=$(echo $1 | sed 's,^DARWIN_OPT_PATH=,,')
58 SUDO=$(echo $1 | sed 's,^SUDO=,,')
61 QUIET=$(echo $1 | sed 's,^QUIET=,,')
64 USE_LINARO=$(echo $1 | sed 's,^USE_LINARO=,,')
67 OOCD_EN=$(echo $1 | sed 's,^OOCD_EN=,,')
70 LIBSTM32_EN=$(echo $1 | sed 's,^LIBSTM32_EN=,,')
73 LIBOPENSTM32_EN=$(echo $1 | sed 's,^LIBOPENSTM32_EN=,,')
75 DEFAULT_TO_CORTEX_M3=*)
76 DEFAULT_TO_CORTEX_M3=$(echo $1 | sed 's,^DEFAULT_TO_CORTEX_M3=,,')
79 CPUS=$(echo $1 | sed 's,^CPUS=,,')
82 echo "Unknown parameter: $1"
87 shift # shifting parameter list to access the next one
90 echo "Settings used for this build are:"
93 echo "DARWIN_OPT_PATH=$DARWIN_OPT_PATH"
96 echo "USE_LINARO=$USE_LINARO"
97 echo "OOCD_EN=$OOCD_EN"
98 echo "LIBSTM32_EN=$LIBSTM32_EN"
99 echo "LIBOPENSTM32_EN=$LIBOPENSTM32_EN"
100 echo "DEFAULT_TO_CORTEX_M3=$DEFAULT_TO_CORTEX_M3"
103 ##############################################################################
104 # Version and download url settings section
105 ##############################################################################
106 if [ ${USE_LINARO} == 0 ] ; then
109 GCC=gcc-${GCCVERSION}
110 GCCURL=http://ftp.gnu.org/gnu/gcc/${GCC}/${GCC}.tar.gz
112 # For the Linaro GCC:
113 GCCRELEASE=4.5-2011.02-0
114 GCCVERSION=4.5-2011.02-0
115 GCC=gcc-linaro-${GCCVERSION}
116 GCCURL=http://launchpad.net/gcc-linaro/4.5/${GCCRELEASE}/+download/${GCC}.tar.bz2
119 BINUTILS=binutils-2.21
128 ##############################################################################
130 ##############################################################################
132 if [ "x${CPUS}" == "x" ]; then
133 if which getconf > /dev/null; then
134 CPUS=$(getconf _NPROCESSORS_ONLN)
139 PARALLEL=-j$((CPUS + 1))
144 echo "${CPUS} cpu's detected running make with '${PARALLEL}' flag"
149 if [ ${DEFAULT_TO_CORTEX_M3} == 0 ] ; then
152 # To default to the Cortex-M3:
153 GCCFLAGS="--with-arch=armv7-m --with-mode=thumb --with-float=soft"
156 # Pull in the local configuration, if any
157 if [ -f local.sh ]; then
161 MAKEFLAGS=${PARALLEL}
164 if [ ${QUIET} != 0 ]; then
166 MAKEFLAGS="${MAKEFLAGS} -s"
169 export PATH="${PREFIX}/bin:${PATH}"
172 SOURCES=${SUMMON_DIR}/sources
173 STAMPS=${SUMMON_DIR}/stamps
176 ##############################################################################
178 ##############################################################################
181 ##############################################################################
182 # OS and Tooldetection section
183 # Detects which tools and flags to use
184 ##############################################################################
188 echo "Found Linux OS."
191 echo "Found Darwin OS."
192 GCCFLAGS="${GCCFLAGS} \
193 --with-gmp=${DARWIN_OPT_PATH} \
194 --with-mpfr=${DARWIN_OPT_PATH} \
195 --with-mpc=${DARWIN_OPT_PATH} \
196 --with-libiconv-prefix=${DARWIN_OPT_PATH}"
197 OOCD_CFLAGS="-I/opt/mine/include -I/opt/local/include"
198 OOCD_LDFLAGS="-L/opt/mine/lib -L/opt/local/lib"
201 echo "Found CygWin that means Windows most likely."
204 echo "Found unknown OS. Aborting!"
209 ##############################################################################
211 # You probably don't have to touch anything after this
212 ##############################################################################
214 # Fetch a versioned file from a URL
216 if [ ! -e ${STAMPS}/$1.fetch ]; then
217 log "Downloading $1 sources..."
218 wget -c --no-passive-ftp $2
219 touch ${STAMPS}/$1.fetch
223 # Log a message out to the console
225 echo "******************************************************************"
227 echo "******************************************************************"
233 # Use 'auto' mode decompression. Replace with a switch if tar doesn't support -a
234 ARCHIVE=$(ls ${SOURCES}/$1.tar.*)
237 echo "archive type bz2"
241 echo "archive type gz"
245 echo "Unknown archive type of $1"
250 ${TAR} xf${TYPE}${TARFLAGS} ${SOURCES}/$1.tar.*
256 ${SUDO} make ${MAKEFLAGS} $2 $3 $4 $5 $6 $7 $8
260 mkdir -p ${STAMPS} ${SOURCES}
264 fetch ${BINUTILS} http://ftp.gnu.org/gnu/binutils/${BINUTILS}.tar.bz2
265 fetch ${GCC} ${GCCURL}
266 fetch ${NEWLIB} ftp://sources.redhat.com/pub/newlib/${NEWLIB}.tar.gz
267 fetch ${GDB} http://ftp.gnu.org/gnu/gdb/${GDB}.tar.bz2
269 if [ ${OOCD_EN} != 0 ]; then
270 if [ ! -e openocd-${OOCD}.tar.bz2 ]; then
271 log "Cloning OpenOCD sources..."
272 git clone git://openocd.git.sourceforge.net/gitroot/openocd/openocd openocd-${OOCD}
276 tar cfvj openocd-${OOCD}.tar.bz2 openocd-${OOCD}
277 #git archive --format=tar --prefix=openocd-${OOCD}/ ${OOCD} | \
278 # bzip2 --stdout > ../openocd-${OOCD}.tar.bz2
279 rm -rf openocd-${OOCD}
283 if [ ${LIBSTM32_EN} != 0 ]; then
284 if [ ! -e libcmsis-${LIBCMSIS}.tar.bz2 ]; then
285 log "Cloning libcmsis sources..."
286 git clone git://git.open-bldc.org/libcmsis.git
288 git archive --format=tar --prefix=libcmsis-${LIBCMSIS}/ ${LIBCMSIS} | \
289 bzip2 --stdout > ../libcmsis-${LIBCMSIS}.tar.bz2
294 if [ ! -e libstm32-${LIBSTM32}.tar.bz2 ]; then
295 log "Cloning libstm32 sources..."
296 git clone git://git.open-bldc.org/libstm32.git
298 git archive --format=tar --prefix=libstm32-${LIBSTM32}/ ${LIBSTM32} | \
299 bzip2 --stdout > ../libstm32-${LIBSTM32}.tar.bz2
304 if [ ! -e libstm32usb-${LIBSTM32USB}.tar.bz2 ]; then
305 log "Cloning libstm32usb sources..."
306 git clone git://git.open-bldc.org/libstm32usb.git
308 git archive --format=tar --prefix=libstm32usb-${LIBSTM32USB}/ ${LIBSTM32USB} | \
309 bzip2 --stdout > ../libstm32usb-${LIBSTM32USB}.tar.bz2
315 if [ ${LIBOPENSTM32_EN} != 0 ]; then
316 if [ ! -e libopenstm32-${LIBOPENSTM32}.tar.bz2 ]; then
317 log "Cloning libopenstm32 sources..."
318 git clone git://libopenstm32.git.sourceforge.net/gitroot/libopenstm32/libopenstm32
320 git archive --format=tar --prefix=libopenstm32-${LIBOPENSTM32}/ ${LIBOPENSTM32} | \
321 bzip2 --stdout > ../libopenstm32-${LIBOPENSTM32}.tar.bz2
329 if [ ! -e build ]; then
333 if [ ! -e ${STAMPS}/${BINUTILS}.build ]; then
336 log "Configuring ${BINUTILS}"
337 ../${BINUTILS}/configure --target=${TARGET} \
346 log "Building ${BINUTILS}"
348 install ${BINUTILS} install
350 log "Cleaning up ${BINUTILS}"
351 touch ${STAMPS}/${BINUTILS}.build
352 rm -rf build/* ${BINUTILS}
355 if [ ! -e ${STAMPS}/${GCC}-${NEWLIB}.build ]; then
359 log "Adding newlib symlink to gcc"
360 ln -f -s `pwd`/${NEWLIB}/newlib ${GCC}
361 log "Adding libgloss symlink to gcc"
362 ln -f -s `pwd`/${NEWLIB}/libgloss ${GCC}
364 if [ ${DEFAULT_TO_CORTEX_M3} == 0 ] ; then
365 log "Patching gcc to add multilib support"
367 patch -p0 -i ../patches/patch-gcc-config-arm-t-arm-elf.diff
372 log "Configuring ${GCC} and ${NEWLIB}"
373 ../${GCC}/configure --target=${TARGET} \
377 --enable-languages="c,c++" \
384 --with-headers=newlib/libc/include \
386 --disable-libstdcxx-pch \
387 --disable-libmudflap \
391 --disable-newlib-supplied-syscalls \
393 log "Building ${GCC} and ${NEWLIB}"
395 install ${GCC} install
397 log "Cleaning up ${GCC} and ${NEWLIB}"
398 touch ${STAMPS}/${GCC}-${NEWLIB}.build
399 rm -rf build/* ${GCC} ${NEWLIB}
402 if [ ! -e ${STAMPS}/${GDB}.build ]; then
405 log "Configuring ${GDB}"
406 ../${GDB}/configure --target=${TARGET} \
412 log "Building ${GDB}"
414 install ${GDB} install
416 log "Cleaning up ${GDB}"
417 touch ${STAMPS}/${GDB}.build
418 rm -rf build/* ${GDB}
421 if [ ${OOCD_EN} != 0 ]; then
422 if [ ! -e ${STAMPS}/openocd-${OOCD}.build ]; then
423 unpack openocd-${OOCD}
425 log "Configuring openocd-${OOCD}"
426 CFLAGS="${CFLAGS} ${OOCD_CFLAGS}" \
427 LDFLAGS="${LDFLAGS} ${OOCD_LDFLAGS}" \
428 ../openocd-${OOCD}/configure --enable-maintainer-mode \
431 --enable-ft2232_libftdi \
432 --enable-usb_blaster_libftdi \
434 --enable-at91rm9200 \
435 --enable-presto_libftdi \
441 log "Building openocd-${OOCD}"
443 install openocd-${OOCD} install
445 log "Cleaning up openocd-${OOCD}"
446 touch ${STAMPS}/openocd-${OOCD}.build
447 rm -rf build/* ${OOCD}
451 if [ ${LIBSTM32_EN} != 0 ]; then
452 if [ ! -e ${STAMPS}/libcmsis-${LIBCMSIS}.build ]; then
453 unpack libcmsis-${LIBCMSIS}
454 cd libcmsis-${LIBCMSIS}
455 log "Building libcmsis-${LIBCMSIS}"
456 make arch_prefix=${TARGET} prefix=${PREFIX}
457 install libcmsis-${LIBCMSIS} arch_prefix=${TARGET} prefix=${PREFIX} install
459 log "Cleaning up libcmsis-${LIBCMSIS}"
460 touch ${STAMPS}/libcmsis-${LIBCMSIS}.build
461 rm -rf libcmsis-${LIBCMSIS}
464 if [ ! -e ${STAMPS}/libstm32-${LIBSTM32}.build ]; then
465 unpack libstm32-${LIBSTM32}
466 cd libstm32-${LIBSTM32}
467 log "Building libstm32-${LIBSTM32}"
468 make arch_prefix=${TARGET} prefix=${PREFIX}
469 install libstm32-${LIBSTM32} arch_prefix=${TARGET} prefix=${PREFIX} install
471 log "Cleaning up libstm32-${LIBSTM32}"
472 touch ${STAMPS}/libstm32-${LIBSTM32}.build
473 rm -rf libstm32-${LIBSTM32}
476 if [ ! -e ${STAMPS}/libstm32usb-${LIBSTM32USB}.build ]; then
477 unpack libstm32usb-${LIBSTM32USB}
478 cd libstm32usb-${LIBSTM32USB}
479 log "Building libstm32usb-${LIBSTM32USB}"
480 make arch_prefix=${TARGET} prefix=${PREFIX}
481 install libstm32usb-${LIBSTM32USB} arch_prefix=${TARGET} prefix=${PREFIX} install
483 log "Cleaning up libstm32usb-${LIBSTM32USB}"
484 touch ${STAMPS}/libstm32usb-${LIBSTM32USB}.build
485 rm -rf libstm32usb-${LIBSTM32USB}
489 if [ $LIBOPENSTM32_EN != 0 ]; then
490 if [ ! -e ${STAMPS}/libopenstm32-${LIBOPENSTM32}.build ]; then
491 unpack libopenstm32-${LIBOPENSTM32}
492 cd libopenstm32-${LIBOPENSTM32}
493 log "Building libopenstm32-${LIBOPENSTM32}"
494 make PREFIX=${TARGET} DESTDIR=${PREFIX}
495 install libopenstm32-${LIBOPENSTM32} PREFIX=${TARGET} DESTDIR=${PREFIX} install
497 log "Cleaning up libopenstm32-${LIBOPENSTM32}"
498 touch ${STAMPS}/libopenstm32-${LIBOPENSTM32}.build
499 rm -rf libopenstm32-${LIBOPENSTM32}