## Results ##
-* Grain 1, g gross, g casting tube, g net propellant
-* Grain 2, g gross, g casting tube, g net propellant
-* Grain 3, g gross, g casting tube, g net propellant
-* Grain 4, g gross, g casting tube, g net propellant
+Forgot to weigh casting tubes, using average from the next couple batches
+instead. Grain 2 visibly under-filled.
+
+* Grain 1, 195.5g gross, 5.8g casting tube, 189.7g net propellant
+* Grain 2, 192.6g gross, 5.8g casting tube, 186.8g net propellant
+* Grain 3, 195.3g gross, 5.8g casting tube, 189.5g net propellant
+* Grain 4, 201.6g gross, 5.8g casting tube, 195.8g net propellant
## Results ##
-* Grain 1, g gross, 5.78g casting tube, g net propellant
-* Grain 2, g gross, 5.82g casting tube, g net propellant
-* Grain 3, g gross, 5.78g casting tube, g net propellant
-* Grain 4, g gross, 5.80g casting tube, g net propellant
+* Grain 1, 198.8g gross, 5.78g casting tube, 193.0g net propellant
+* Grain 2, 194.1g gross, 5.82g casting tube, 188.3g net propellant
+* Grain 3, 196.6g gross, 5.78g casting tube, 190.8g net propellant
+* Grain 4, 201.1g gross, 5.80g casting tube, 195.3g net propellant
## Results ##
-* Grain 1, g gross, 5.78g casting tube, g net propellant
-* Grain 2, g gross, 5.87g casting tube, g net propellant
-* Grain 3, g gross, 5.83g casting tube, g net propellant
-* Grain 4, g gross, 5.79g casting tube, g net propellant
+* Grain 1, 193.4g gross, 5.78g casting tube, 187.6g net propellant
+* Grain 2, 192.5g gross, 5.87g casting tube, 186.6g net propellant
+* Grain 3, 190.8g gross, 5.83g casting tube, 185.0g net propellant
+* Grain 4, 195.1g gross, 5.79g casting tube, 189.3g net propellant
--- /dev/null
+# Test 2018-1 #
+
+7 grain 75mm sorbitol motor with pyrodex pellet ignition in 4-inch Wildman
+rebuilt airframe flown on 2 September 2018 at Airfest in Argonia, KS.
+
+CTI Pro75 6xl case, Loki #50 (long) nozzle with 2 o-rings, CTI forward and aft
+closure rings, forward bulkhead from Terry's pile machined to have 0.5" inside
+snap ring plus 0.25" inside liner, with two o-rings, one pushing against liner.
+Original simulation says this should be a a 34% M-2293 with 6520 Ns total
+impulse, 1056 psi max, 76% volume loading, and about 2.25 seconds burn
+time. After casting and weighing the grains, the adjusted simulation says
+this will be a ...
+
+## Results ##
+
+Flown at Airfest in Argonia, KS, off Terry's launch trailer. Motor cato'd
+about 0.45 seconds after launch, blowing forward closure through the ebay
+and ripping the forward end of the case apart violently. Clearly a
+significant over-pressure event. Pretty sure this was the first time I
+actually few the Pro75 6xl case with KNSB, and I dialed up the max pressure
+at the same time... which was clearly a bad plan.
+
+The burning grains were sent up in a fireworks-display-worthy fashion,
+generally acknowledged as the most impressive-looking CATO of the weekend.
+
+Flight data logged as sn 3121, flight 5, stored in cato.eeprom.
+
--- /dev/null
+# Batch 2019.01.07 #
+
+4 Terry-length Everyclear grains for 54mm cases, with 0.5 inch cores,
+cast as two 6-inch-long double grains then cut and trimmed.
+
+This was my first time mixing APCP propellant. Used the 4.5qt mixer and
+hand packed with no vacuum processing. The formula was taken from a pdf
+about everclear, modified by me to use PAPI as the curative.
+
+These grains were cast on 2019-01-07.
+
+## Results ##
+
+The batch size was too small, there was about 1/4" of the second casting
+tube left empty.
+
+* Grain 1, gross, g casting tube, g net propellant
+* Grain 2, gross, g casting tube, g net propellant
+* Grain 3, gross, g casting tube, g net propellant
+* Grain 4, gross, g casting tube, g net propellant
+
+
--- /dev/null
+# Batch 2019.01.08 #
+
+4 Terry-length Everyclear grains for 54mm cases, with 0.5 inch cores,
+cast as two 6-inch-long double grains then cut and trimmed.
+
+This was my second time mixing APCP propellant. Again used the 4.5qt mixer
+and hand packed with no vacuum processing. Same formula as yesterday
+
+These grains were cast on 2019-01-08.
+
+## Results ##
+
+The updated batch size was just right, there was a bit of excess propellant
+so we can make density and burn rate measurements after cure.
+
+* Grain 1, gross, g casting tube, g net propellant
+* Grain 2, gross, g casting tube, g net propellant
+* Grain 3, gross, g casting tube, g net propellant
+* Grain 4, gross, g casting tube, g net propellant
+
## Activity Log ##
+### 2019 ###
+
+* [2019 batch 01](2019.01.07.html) - 7 January 2018 - 4 54mm Everclear APCP grains
+* [2019 batch 02](2019.01.08.html) - 8 January 2018 - 4 54mm Everclear APCP grains
+
### 2018 ###
* [2018 batch 01](2018-batch-01.html) - 5 July 2018 - 7 75mm KNSB grains
+* [2018 test 01](2018-test-1.html) - 2 September 2018 - 7-grain 75mm KNSB cato
* [2018 batch 02](2018-batch-02.html) - 15 December 2018 - 4 54mm KNSB grains
* [2018 batch 03](2018-batch-03.html) - 17 December 2018 - 4 54mm KNSB grains
* [2018 batch 04](2018-batch-04.html) - 17 December 2018 - 4 54mm KNSB grains