add a paragraph about TeleBT battery charging to AltosDroid chapter in documentation

diff --git a/ao-bringup/turnon_telebt b/ao-bringup/turnon_telebt
deleted file mode 100755 (executable)
index f4100ae..0000000
--- a/ao-bringup/turnon_telebt
+++ /dev/null
@@ -1,62 +0,0 @@
-#!/bin/sh
-
-if [ -x ../ao-tools/ao-load/ao-load ]; then
-       AOLOAD=../ao-tools/ao-load/ao-load
-elif [ -x /usr/bin/ao-load ]; then
-       AOLOAD=/usr/bin/ao-load
-else
-       echo "Can't find ao-load!  Aborting."
-       exit 1
-fi
-
-if [ -x ../ao-tools/ao-rawload/ao-rawload ]; then
-       RAWLOAD=../ao-tools/ao-rawload/ao-rawload
-elif [ -x /usr/bin/ao-rawload ]; then
-       RAWLOAD=/usr/bin/ao-rawload
-else
-       echo "Can't find ao-rawload!  Aborting."
-       exit 1
-fi
-
-echo "TeleBT v1.1 Turn-On and Calibration Program"
-echo "Copyright 2013 by Bdale Garbee.  Released under GPL v2"
-echo
-echo "Expectations:"
-echo "\tTeleBT v1.1 powered from USB"
-echo "\t\twith TeleDonlge (on /dev/ttyACM0) cabled to debug header"
-echo "\t\twith coax from SMA to frequency counter"
-echo
-echo -n "TeleBT serial number: "
-read SERIAL
-
-echo $RAWLOAD
-
-case $USER in
-    bdale)
-       DONGLE=100
-       ;;
-    keithp)
-       DONGLE=186
-       ;;
-    *)
-       echo "Unknow user"
-       exit 1
-       ;;
-esac
-
-$RAWLOAD -D $DONGLE -r ao_led_blink.ihx
-echo "LEDs should be blinking"
-sleep 5
-
-$RAWLOAD -D $DONGLE -r ao_radio_xmit.ihx
-echo -n "Generating RF carrier.  Please enter measured frequency: "
-read FREQ
-
-CAL_VALUE=`nickle -e "floor(434.55 / $FREQ * 1186611 + 0.5)"`
-
-echo "Programming flash with cal value " $CAL_VALUE
-$AOLOAD -D $DONGLE --cal $CAL_VALUE ~/altusmetrumllc/Binaries/telebt-v1.0*.ihx $SERIAL
-
-echo "Serial number "$SERIAL" programmed with RF cal value "$CAL_VALUE
-echo $SERIAL","$CAL_VALUE >> cal_values
-echo "Unplug debug cable, power cycle, cu to the board, confirm freq and record power"

diff --git a/ao-bringup/turnon_telebt_v1 b/ao-bringup/turnon_telebt_v1
new file mode 100755 (executable)
index 0000000..f4100ae
--- /dev/null
+++ b/ao-bringup/turnon_telebt_v1
@@ -0,0 +1,62 @@
+#!/bin/sh
+
+if [ -x ../ao-tools/ao-load/ao-load ]; then
+       AOLOAD=../ao-tools/ao-load/ao-load
+elif [ -x /usr/bin/ao-load ]; then
+       AOLOAD=/usr/bin/ao-load
+else
+       echo "Can't find ao-load!  Aborting."
+       exit 1
+fi
+
+if [ -x ../ao-tools/ao-rawload/ao-rawload ]; then
+       RAWLOAD=../ao-tools/ao-rawload/ao-rawload
+elif [ -x /usr/bin/ao-rawload ]; then
+       RAWLOAD=/usr/bin/ao-rawload
+else
+       echo "Can't find ao-rawload!  Aborting."
+       exit 1
+fi
+
+echo "TeleBT v1.1 Turn-On and Calibration Program"
+echo "Copyright 2013 by Bdale Garbee.  Released under GPL v2"
+echo
+echo "Expectations:"
+echo "\tTeleBT v1.1 powered from USB"
+echo "\t\twith TeleDonlge (on /dev/ttyACM0) cabled to debug header"
+echo "\t\twith coax from SMA to frequency counter"
+echo
+echo -n "TeleBT serial number: "
+read SERIAL
+
+echo $RAWLOAD
+
+case $USER in
+    bdale)
+       DONGLE=100
+       ;;
+    keithp)
+       DONGLE=186
+       ;;
+    *)
+       echo "Unknow user"
+       exit 1
+       ;;
+esac
+
+$RAWLOAD -D $DONGLE -r ao_led_blink.ihx
+echo "LEDs should be blinking"
+sleep 5
+
+$RAWLOAD -D $DONGLE -r ao_radio_xmit.ihx
+echo -n "Generating RF carrier.  Please enter measured frequency: "
+read FREQ
+
+CAL_VALUE=`nickle -e "floor(434.55 / $FREQ * 1186611 + 0.5)"`
+
+echo "Programming flash with cal value " $CAL_VALUE
+$AOLOAD -D $DONGLE --cal $CAL_VALUE ~/altusmetrumllc/Binaries/telebt-v1.0*.ihx $SERIAL
+
+echo "Serial number "$SERIAL" programmed with RF cal value "$CAL_VALUE
+echo $SERIAL","$CAL_VALUE >> cal_values
+echo "Unplug debug cable, power cycle, cu to the board, confirm freq and record power"

diff --git a/doc/altusmetrum.xsl b/doc/altusmetrum.xsl
index a40481f16c83b2253194f9f6d118ed1ad67277f1..d1328abf653027d6566981327e3f87387a274b46 100644 (file)
--- a/doc/altusmetrum.xsl
+++ b/doc/altusmetrum.xsl
@@ -3989,6 +3989,18 @@ NAR #88757, TRA #12200
        from which you can download and install the application.
       </para>
     </section>
+    <section>
+      <title>Charging TeleBT Battery</title>
+      <para>
+       Before using TeleBT with AltosDroid, make sure the internal 
+       TeleBT battery is charged.  To do this, attach a micro USB
+       cable from a computer or other USB power source to TeleBT.
+       A dual LED on the circuit board should illuminate, showing
+       red while the battery is charging, green when charging is
+       completed, and both red and green on at the same time if
+       there is a battery fault.
+      </para>
+    </section>
     <section>
       <title>Connecting to TeleBT over Bluetooth™</title>
       <para>